Effects of yaw-roll coupling ratio on lateral-directional aerodynamic characteristics

Experimental investigation of large amplitude yaw-roll coupled oscillations was conducted in a low-speed wind tunnel using an aircraft configuration model. A special test rig was designed and constructed to provide different coupled motions from low to high angles of attack.A parameter ‘‘coupling ratio" was introduced to indicate the extent of yaw-roll coupling. At each pitch angle, seven coupling ratios were designed to study the yaw-roll coupling effects on the lateraldirectional aerodynamic characteristics systematically. At high angles of attack, the damping characteristics of yawing and rolling moments drastically varied with coupling ratios. In the coupled motions with the rotation taking place about the wind axis, the lateral-directional aerodynamic moments exhibited unsteady characteristics and were different from the ‘‘quasi-steady" results of the rotary balance tests. The calculated results of the traditional aerodynamic derivative method were also compared with the experimental data. At low and very high angles of attack, the aerodynamic derivative method was applicative. However, within a wide range of angles of attack, the calculated results of aerodynamic derivative method were inconsistent with the experimental data, due to the drastic changes of damping characteristics of lateral-directional aerodynamic moments with yaw-roll coupling ratios.     

过冷水滴凝固机理及凝固组织特征

针对飞机过冷水滴结冰的精细化预测需求，基于相变热力学与相变动力学相关理论，采用示差扫描量热法（DSC）、结冰风洞试验及微结构测试相结合的方法，研究了过冷水滴凝固过程的热力学机理及凝固组织特征。基于示差扫描量热法，研究了冷却速率及形核条件对结晶凝固特性的影响规律；基于结冰风洞试验开展了不同温度条件下冰相的宏观形貌及微结构特征研究。结果表明，过冷条件及冷却速率是影响过冷水滴结晶速率及结晶完善程度的重要因素。降温速率越大，结晶速率常数增大、结晶速率相应提高。同时，结晶峰变宽，结晶初始温度向低温方向移动，过冷效应相对显著；反之亦然。过冷度及冷却速率对冰相的宏观及微观形貌均有着重要影响。过冷度越大则相同时间内冷却速率越大，晶体生长过程越不充分，晶体不规则程度相对较高，同时晶粒密度变大、尺度变小，冰相表观透明度相对降低；反之，过冷度越小，则晶粒密度变小、尺度变大，冰相表观透明度相对较高。异相形核条件对加速结晶过程有重要促进作用，晶种的存在可有效加速二次结晶的触发，使过冷效应显著减弱。相关研究可为飞机结冰速率、冰相物理特征及冰形宏观形貌的精细化预测提供参考。     

超高速机械密封副离子注入与摩擦学特性研究

超高速机械动密封需满足CZ-5运载火箭伺服系统中涡轮泵可靠性及寿命指标要求。离子注入作为重要的金属材料表面改性技术，对有效改善机械密封副旋转环表面摩擦磨损特性至关重要。在对密封动环表面离子注入可行性研究的基础上，提出了对其密封副配对摩擦磨损特性进行综合验证的试验方案。通过选取常用典型石墨与旋转金属环配副进行干磨条件下的试验测试，改变线速度、端面比压，使用摩擦磨损试验机对比分析了配对摩擦副的摩擦磨损特性，系统研究了载荷和转速对密封副配对摩擦系数的影响规律，揭示其密封摩擦学特性。通过机械密封在温度应力下的工作可靠性分析以及密封副整机稳态工作性能验证，为超高速涡轮泵的寿命与可靠性试验验证提供了一个合理的、高效费比的技术途径。     

摆线桨非定常动态失速的三维效应

对摆线桨三维全尺寸模型进行了非定常数值模拟。验证了两种嵌套网格方法的可靠性与适用性,针对二维/三维情况下摆线桨非定常涡流动特性及诱导分离特性开展了数值分析,重点研究了展向气动力随方位角的分布与全局流场的诱导速度分布,并分析了尾迹捕捉精度与涡量耗散特征。结果表明:受摆线桨切向速度、展向诱导速度等三维效应影响,两种计算结果的瞬态气动力极值差值达到44%。三维动态失速涡的产生、脱落与再附明显弱于二维翼型情况,这对于摆线桨非定常气动特性有较大影响。      

Applications of structural efficiency assessment method on structural-mechanical characteristics integrated design in aero-engines

In the design process of advanced aero-engines, it is necessary to carry out an effective analysis method between structural features and mechanical characteristics for a better structural optimization. Based on the structural composition and functions of aero-engines, the concept and contents of structural efficiency can reflect the relation between structural features and mechanical characteristics. In order to achieve the integrated design of structural and mechanical characteristics, one quantitative analysis method called Structural Efficiency Assessment Method (SEAM) was put forward. The structural efficiency coefficient was obtained by synthesizing the parameters to quantitatively evaluate the aero-engine structure design level. Parameterization method to evaluate structural design quality was realized. After analyzing the structural features of an actual dual-rotor system in typical high bypass ratio turbofan engines, the mechanical characteristics and structural efficiency coefficient were calculated. Structural efficiency coefficient of high-pressure rotor (0.43) is higher than that of low-pressure rotor (0.29), which directly shows the performance of the former is better, there is room for improvement in structural design of the low-pressure rotor. Thus the direction of structural optimization was pointed out. The applications of SEAM shows that the method is operational and effective in the evaluation and improvement of structural design.     

Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

多自由度振动环境下惯组非线性传递特性研究

惯组作为飞行器姿控系统的传感器,其局部安装结构的传递特性的测量精度直接关系到导航精度。目前,惯组普遍使用减振器进行隔振,而减振器都呈现出较强的非线性特征。为了考察惯组在不同工况下的传递特性,将惯组简化为六自由度Duffing模型,推导了基础激励下系统的运动微分方程,并用龙格-库塔法对方程进行求解,分析了自由衰减振动和强迫振动下不同工况的系统传递特性。结果表明,多自由度激励比单自由度激励工况得到的系统传递特性的频率和幅值都低。考虑到惯组真实的使用环境,应当在多自由度振动环境下进行传递特性试验。     

亚超剪切混合层燃油雾化特性试验研究

为了摸清亚超大梯度剪切混合层内直射式喷嘴的燃油雾化特性，设计了用于向亚超剪切混合流中进行燃油喷射的直射式喷嘴，建立了亚超剪切混合层中燃油雾化试验系统。利用粒子图像测速系统（PIV），对亚超大梯度混合层中油雾场进行测量。通过改变喷嘴流量、喷射角度和喷嘴数量研究不同参数对雾化特性的影响，并应用图像处理技术对亚超大梯度剪切混合层内的油雾场进行分析，总结归纳其雾化规律。试验结果显示：随着流量增大，穿透深度会随之增大，破碎后的颗粒分布峰值所对应的液滴直径会逐渐变小，雾化效果提升；相同流量条件下，喷嘴的角度改变对雾化效果有影响，顺喷和逆喷的雾化效果均好于垂直喷射；逆喷的喷射高度最高，随着流量的增长，燃料将会碰壁；顺喷条件下，随着角度的增加，穿透长度会有所增加；综合燃油轨迹边界，逆喷的效果相对较好。相同流量条件下，喷孔个数的改变对雾化效果和穿透深度的影响不大。     

基于混合深度特征的红外目标抗干扰识别算法

复杂干扰条件下的红外空中目标识别技术是空战对抗领域的热点研究课题,复杂人工干扰严重遮蔽目标,导致目标特征的连续性与显著性遭到破坏,无法全面描述识别对象的特性,造成空中目标识别准确率下降。针对此问题,提出一种基于图像混合深度特征的空中目标抗干扰识别算法。首先,基于卷积神经网络进行图像深度特征的提取,将深度特征与梯度直方图(Histogram of Gradient, HOG)特征进行有效融合,构建混合深度特征。针对作战场景中的目标与干扰的对抗态势多样性,将支持向量机的二分类模型改进为三分类模型,对目标、干扰以及目标干扰粘连三种状态进行精确分类。实验结果表明：在复杂干扰环境下,基于混合深度特征的空中目标抗干扰识别算法正确率为92.29%,该算法可以有效地解决目标被干扰遮蔽、形成目标干扰粘连状态时的抗干扰识别问题。     

湍流控制屏声学校准及校准精度影响因素

湍流控制屏（TCS）是航空发动机风扇噪声试验必备的试验设施。由于湍流控制屏的作用,风扇前传噪声向远场传播时会产生传递损失。通过对湍流控制屏的声学校准,可以获取湍流控制屏的声学修正量,从而实现对风扇前传噪声的修正。本文结合实际工程应用条件,分析了湍流控制屏重复安装的位置精度、校准声源重复性、稳定性、校准声源位置偏差、温湿度修正等因素对湍流控制屏声学修正量精度的影响;结合上述影响因素,对湍流控制屏160 Hz~40 kHz的声学修正量的特征进行分析,总结工程应用中湍流控制屏高精度声学校准的注意事项,提出湍流控制屏的声学校准应包含测量不确定度。